0-10V Dimmer Module (L+N)

Product Description
  1. Reset Key
  2. Indicator Light
  3. Mounting Clip
Product Size
  • Without Mounting Clip
    • W: 46 mm
    • H: 46 mm
    • D: 18 mm
  • With Mounting Clip
    • W: 50 mm
    • H: 46 mm
    • D: 22.5 mm
Technical specification

Power supply mode

100-240V AC 50-60 Hz

Connectivity

Zigbee

Frequency

2.4GHz-2.484GHz

Wiring

N - Neutral L - Line

Panel material

ABS+PC material

Product color

White

Number of channels

1 channel

Operation range

200m

Operating Temperature °C

-10°C - +40°C

Operating Temperature °F

+14°F - +104°F

Operating Humidity % RH

≤ 80% RH

Safety features

Overload, Over Voltage, Short Circuit, Thermal Protection, Static Protection, Surge Protection

IP rating

IP20

Max Load

400W (LED lighting)

Installation

Warnings:

  • Installation must be carried out by a qualified electrician in accordance with local regulations.
  • Keep the device out of reach of children.
  • Keep the device away from water , damp or hot environments.
  • Install the device away from strong signal sources such as microwave ovens that may cause signal interruption resulting in abnormal operation of the device.
  • Obstruction by concrete wall or metallic materials may reduce the effective operation range of the device and should be avoided.
  • Do NOT attempt to disassemble, repair or modify the device.
Wiring Instructions and Diagrams
  1. Safety First
    1. Always disconnect power before installation.
    2. Only trained professionals should perform the work.
    3. Comply with all relevant local and national codes (e.g., NEC, IEC).
       
  2. Installation Steps
    1. Isolate Power
      Switch off the breaker and verify zero voltage.
    2. Wire the Module
      Connect terminals as per the wiring diagram:
      Live (L), Neutral (N), Load
      Optional: Control input (e.g., switch)
    3. Install in Box
      Place the module into the junction box. Avoid wire damage or strain.
    4. Restore Power & Configure
      Turn the power back on. Configure the module using the app or setup guide.

Tip: Keep your phone close to the module during setup (e.g., for Bluetooth or NFC pairing).

  • With One Switch
  • With Two Switch
  • Without Switch
Manual Override

The dimmer module reserves the access of manual override function for the end-user to switch on/off, or adjust the light level by push-switch.

  • Short Push (<1s): permanent on/off function.
  • Long Push (>1s): adjust the brightness level.
     

Notes:

  • Both the adjustment on App and push switch can overwrite each other, the last adjustment remains in memory.
  • App control is synchronized with the manual switch.
  • The “S” terminals may be left unconnected if no manual control is required.

Reset Methods:

  1. Option:
  • Press and hold the reset button for about 10 seconds until either:
  • the indicator light starts flashing rapidly, or
  • the connected light begins to flash quickly.
  1. Option:
  • Turn off the external manual switch.
  • Then, press and hold the external button switch for about 10 seconds, until the indicator light or the connected light starts flashing quickly.
  1. Option:
  • Turn off the device completely.
  • Turn it on and leave it powered for about 10 seconds.
  • Then, turn the device off and on 5 times in a row.

Important:

  • Each power OFF time should last more than 3 seconds.
  • Each power ON time should last less than 2 seconds.
System requirements

The PIERRE Wave system is a user-friendly solution for integrating and managing smart devices through a central platform. The system consists of the following components:

A - Required Elements:

  1. PIERRE Wave Products: These smart devices, including lighting, thermostats, sensors, and other appliances, connect wirelessly to the PIERRE Wave Gateway. They provide essential functions and capabilities for the system.
  2. PIERRE Wave Gateway: The central unit linking all PIERRE Wave devices, the gateway manages communication and data exchange, ensuring security and stability. It supports remote access and control, with the default Berlin display interface, though users can choose any PIERRE display model.

B - Optional Elements:

  1. Mobile PIERRE App: This app allows users to manage and monitor the system from their smartphone or tablet, offering real-time updates and remote access. It provides convenience but is not necessary for basic system operation.
  2. Router: An optional component that enables internet connectivity, allowing devices to be accessed and controlled remotely.
  1. System Operation: The gateway can connect to the router via Wi-Fi or LAN for internet connectivity, enhancing remote management capabilities. PIERRE Wave products communicate wirelessly with the gateway, which acts as the central hub. This bidirectional communication allows data to flow both ways, enabling users to send commands and receive status updates through the Mobile PIERRE App. The app facilitates effective management and real-time feedback on device statuses.
App-to-Device Pairing

Please scan the QR code to download PIERRE application
 

Log in with you Username and Password
 

Open Settings and press "Add Wave I/O"
 

Press and hold the Reset Key for 10 seconds (use a small, thin object like a paperclip) until the Indicator Light starts flashing

  1. Indicator Light
  2. Reset Key
  3. PIERRE Wave Gateway 
     

Press "Find Devices"
 

PIERRE application will show the list of available devices. Press "Add found devices"
 

Enter Name, Role and Group settings and Save it
 

When the Light indicator stops flashing, the PIERRE Wave pairing process is finished
 

FAQ

Q1: What should I do if I can’t configure the dimmer module? 

  • Please check whether the device is powered on.
  • Make sure the PIERRE Gateway is available.
  • Make sure the wiring is correct. 


Q2: What device can be connected to this PIERRE dimmer module? 

It can be connected to devices such as triac led light, incandescent lamp or halogen lamp.

Q3: What happens if the WIFI goes off? 

You can still control the device connected to the switch module with your traditional switch and with PIERRE Displays. 

Q4: How do I reset the device? 

  1. Switch the button for 10 times, and wait for about 10s until the indicator light of the module flashes quickly.
  2. Press the reset key for about 10s until the indicator light of the module flashes quickly.